This product is no longer in stock
Warning: Last items in stock!
RTL8188SU Single-Chip IEEE 802.11b/g/n 1T1R WLAN Controller with USB 2.0 Interface
The Realtek RTL8188SU-GR is a highly integrated single-chip Wireless LAN (WLAN) USB 2.0 network interface controller compatible with the IEEE 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip. The RTL8188SU-GR provides a complete solution for a high-performance wireless client.
The RTL8188SU-GR baseband implements Multiple Input, Multiple Output (MIMO) Orthogonal Frequency Division Multiplexing (OFDM) with one transmit and one receive path (1T1R). Features include one spatial stream transmission, short Guard Interval (GI) of 400ns, spatial spreading, and support for both 20MHz and 40MHz channel bandwidth.
For legacy compatibility, Direct Sequence Spread Spectrum (DSSS), Complementary Code Keying (CCK) and OFDM baseband processing are included to support all IEEE 802.11b, and 802.11g data rates. Differential phase shift keying modulation schemes, DBPSK and DQPSK with data scrambling capability are available, and CCK provides support for legacy data rates, with long or short preamble. The high speed FFT/IFFT paths, combined with BPSK, QPSK, 16QAM, and 64QAM modulation of the individual subcarriers, and rate compatible punctured convolutional coding with coding rate of 1/2, 2/3, 3/4, and 5/6, provide higher data rates of 54Mbps and 150Mbps for IEEE 802.11g and 802.11n OFDM respectively.
The RTL8188SU-GR builds in an enhanced signal detector, an adaptive frequency domain equalizer, and a soft-decision Viterbi decoder to alleviate severe multi-path effects and mutual interference in the reception of multiple streams. Robust interference detection and suppression are provided to protect against Bluetooth, cordless phone, and microwave oven interference.
Efficient IQ-imbalance, DC offset, phase noise, frequency offset, and timing offset compensations are provided for the radio frequency front-end. Selectable digital transmit and receive FIR filters are provided to meet transmit spectrum mask requirements and to reject adjacent channel interference, respectively.
The RTL8188SU-GR supports fast receiver Automatic Gain Control (AGC) with synchronous and asynchronous control loops among antennas, antenna diversity functions, and adaptive transmit power control functions to obtain better performance in the analog portions of the transceiver.
The RTL8188SU-GR MAC supports 802.11e for multimedia applications, 802.11i for security, and 802.11n for enhanced MAC protocol efficiency. Using packet aggregation techniques such as A-MPDU with BA and A-MSDU, protocol efficiency is significantly improved. Power saving mechanisms such as Legacy Power Save and U-APSD reduce power wasted during idle time, and compensate for the extra power required to transmit OFDM. The RTL8188SU-GR provides simple legacy and 20MHz/40MHz co-existence mechanisms to ensure backward and network compatibility.
CMOS MAC, Baseband PHY and RF in a single chip for IEEE 802.11b/g/n compatible WLAN
72.2Mbps receive PHY rate and 72.2Mbps transmit PHY rate using 20MHz bandwidth
150Mbps receive PHY rate and 150Mbps transmit PHY rate using 40MHz bandwidth
Compatible with 802.11n specification
Backward compatible with 802.11b/g devices while operating at 802.11n data rates
Complies with USB 2.0
IEEE 802.11b/g/n compatible WLAN
IEEE 802.11e QoS Enhancement (WMM)
IEEE 802.11i (WPA, WPA2). Open, shared key, and pair-wise key authentication services
Cisco Compatible Extensions (CCX4)
Frame aggregation for increased MAC efficiency (A-MSDU, A-MPDU)
Low latency immediate High-Throughput Block Acknowledgement (HT-BA)
Long NAV for media reservation with CF-End for NAV release
PHY-level spoofing to enhance legacy compatibility
Power saving mechanism
Channel management and co-existence
Multiple BSSID feature allows the RTL8188SU-GR to assume multiple MAC identities when used as a wireless bridge
Supports Wake-On-WLAN via Magic Packet and Wake-up frame
Transmit Opportunity (TXOP) Short Inter-Frame Space (SIFS) bursting for higher multimedia bandwidth
Complies with USB Specification 2.0
Supports Full-speed (12Mbps) and High-speed (480Mbps)
General Purpose Input/Output (8 pins)
4-wire EEPROM control interface (93C46)
Two configurable LED pins
Configurable Bluetooth Coexistence Interface
IEEE 802.11n OFDM
One Transmit and one Receive path (1T1R)
20MHz and 40MHz bandwidth transmission
Short Guard Interval (400ns)
DSSS with DBPSK and DQPSK, CCK modulation with long and short preamble
OFDM with BPSK, QPSK, 16QAM, and 64QAM modulation. Convolutional Coding Rate: 1/2, 2/3, 3/4, and 5/6
Maximum data rate 54Mbps in 802.11g, and 150Mbps in 802.11n
Switch diversity for DSSS/CCK
Hardware antenna diversity
Selectable digital transmit and receive FIR filters
Programmable scaling in transmitter and receiver to trade quantization noise against increased probability of clipping
Fast receiver Automatic Gain Control (AGC)
On-chip ADC and DAC
Single-Band 11n 1x1 Application (MAC/BB/RF + PA)
Windows 2000, XP 32/64, Vista 32/64, Windows 7, Windows 8, Windows 10 Linux, Mac Power PC& PC,
|WiFi Chipset||Realtek RTL8811AU|
We accept orders by the following methods:
Online (secure): browse our range and add products to your basket.
Offline: please see the contact us page for telephone, fax, and email details (you can change your country by clicking on the link at the top of the page). Shipping prices vary across our product range and can be viewed for each product on the product datasheet by choosing the country you are in.
Express international delivery & worldwide shipping.
All in-stock orders received Monday through Fridays are shipped the same day. For customers in Europe, the deadline for same day dispatch is 16:00pm. Orders received after these deadlines are shipped the next business day. You can check availability by viewing the datasheet which will display a yellow check mark if the product is in stock availability check mark.
Quality is important to Siliceo online Therefore if a product does not perform as described on the datasheet please notify us within 24 months of delivery using the contact form and our dedicated team of scientific experts will examine details of your protocol to determine whether the problem is protocol related or product related.
All payment details are described on the invoice that you will receive after your order is dispatched. The invoice will be sent to the billing address you specify and this can be different to the delivery address for the products.
We accept PayPal, credit card, cash on delivery, bank and wire transfer as methods of payment, for further details please contact us.