WORKS WITH ALL OPERATING SYSTEMS
WINDOWS XP, Vista system (32-64)，win7 operate system (32-64) WINDOWS 8，Mac OS system. Linux, ANDROID
(EXPERIMENTALLY TESTED ON ANDROID VERSIONS FROM 2.3 TO 4.5 and below)
Low battery consumption
The GPS receiver BU-353-S4 IS THE LATEST MODEL OF GPS RECEIVER. FOR VEHICLE, BOAT, AIRCRAFT, MOTORCYCLE ETC. Chip Prolific PL2303 compatible cvon WAAS is magnetic and waterproof with a non-slip base. Has the latest GPS chipset SiRF Star IV, and with a patch antenna for a better signal precision. Their applications include and are not limited to, marine, aerial, and commercial, fire trucks, police cars, buses, utility vehicles and the long-distance transport. The cable is long 1.5 m and has a USB connector on its end to connect with a laptop computer / ibook. / PowerBook.
COMPATIBLE ALL WINDOWS XP VISTA / WIN 7 / WIN 8 / LINUX / MAC
PC, LAPTOP, TABLET OR NETBOOK ADAPTER USB GPS TO NAVIGATE ON-SCREEN
Globalsat BU-353 S4 (SiRF Star IV)
USB GPS receiver - CD-ROM driver with user's Guide and test utility for WIN and Mac o / S *
GPS receivers Globalsat USB require a laptop computer with a Windows or Macintosh with a CDROM *,
USB port and a navigation software compatible with NMEA. The mapping / navigation of third-party
the software may have its own system requirements, please refer to the software vendor for more information. Characteristics Electrical Characteristics (Receiver)
Chipset GPS: SiRF STAR IV GSD4e
Frequency: L1, 1575.42 MHZ
C / A code: speed of chip 1.023 MHz
Horizontal position: <2.5 m 2D RMS SBAS Enable
Speed: 0.1 m / sec 95% (SA off),
Time: 1 micro-second synchronized with the time of the GPS
WAAS: enabled for products of North America (USGlobalSat, Inc)
Acquisition rate hot Start: 8 sec., Average
Warm start: 35 sec., Average
Cold start: 35 sec., Average
Remapping: 0.1 sec. average
Protocol Protocol GPS Default: NMEA 0183 (Secondary: SiRF binary) SiRF binary >> position, velocity, altitude, status and control
NMEA 0183 protocol MEA0183 V3.0 and supports
Output data GPS: command GGA, GSA, GSV, RMC, VTG, GLL v2.2 (VTG and GLL are optional)
Speed of transfer of GPS: settings of the software command (default: 4800, n, 8,1 for NMEA)
Dynamic acceleration of the condition: limit less than 4g
Altitude limit: 18,000 meters (60,000 feet) max.
Speed limit: 515 meters / sec. (1,000 knots) max.
Jerk Limit: 20 m / sec ** 3
Operating temperature: -40 ° ~ 80 ° C
Storage: -40 ° ~ 85 ° C
Humidity: up to 95% non-condensing
Voltage of power: 5V ± 5%
Current: 60mA typical
Dimension: 2.32 "x 1.65" x 0.82 "(59mm x 47 mm x 21 mm)
USB cable length: 60 "(152 cm)
Amplifier low noise Amplifier Gain w / out cable: 27 dB Typical
Filtering: -25dB (+100 MHz)
VSWR output: 2.0 max.
Voltage: DC 3 ~ 5.0 V
Current: 15mA max @ 5VDC
SILICEA - SILICEOTOOLS ©
TESTED ON ANDROID VERSIONS FROM 2.3 TO 4.4 and Android 5.0
INSTALL USB GPS ANDROID
We NEED to:
- ANDROID TABLET WITH PERMISSIONS (does not need ROOT permissions) WITH A USB HOST PORT. Also works with micro-USB port on the Host.
- ADAPTER USB GPS SILICON or ND-100S with chip Prolific PL2303 USB-serial UART GPS
- VALID FOR ALL VERSIONS OF ANDROID FROM 2.3 TO 4.4
* It is nececesario install two applications for android:
- Prolific PL2303 USB-UART (can be downloaded from Play Store )
- UsbGPS4Honeycomb_MR1_alpha.apk Download-> UsbGPS4Honeycomb_MR1_alpha.apk
The procedure is simple. You just need to install two applications.
This GPS works with the driver for PROLIFIC PL2303. The module that you need to install is the pl2303.ko, in the folder modules of your Tablet. It has to be compiled for the kernel your version of Android. You can locate files update Tablet or on the network. Examples of locations of the modules in different tablet:
The app Prolific PL2303 USB-UART installing this module driver on your Tablet or Android phone
You will find the app easily in the android market, Play Store or in the page of Prolific.
Once you have installed this application provides your Tablet the necessary connection to recognize the adapter GPS. All GPS transmit data through a serial port, so it is necessary to adapt the Tablet with the driver PROLIFIC pl2303. Open the app and in options (settings) configures the transmission speed of 4800 baud rate.
For the external GPS to work we need to enable the option of location to be simulated. “Settings – Applications -- Development – Allow mock locations” Mock Location” “Allow mock locations”
In addition, an application must transmit the reading data from the GPS to the system in the mode NMEA. This application is UsbGPS4Honeycomb_MR1_alpha.apk
OPERATION OF THE GPS:
Insert the GPS the USB port. Open the app UsbGps normally chooses the device automatically in dev/bus/usb/001/001. You can also manually select. Click Start GPS to begin reading data.
** Note The GPS takes a chip SIRF III that transmits data at a speed of 4800 baud rate. If it is necessary, order that-speed from console with: “stty -F /dev/ttyUSB0 ispeed 4800” With the command “cat < /dev/ttyUSB0” we can see from the console the data read by the GPS. Other models of GPS can works r at a different speed, to configure for each case, the baud rate correct.
THE USB GPS IS READY TO NAVIGATE WITH MAPS
*** Remember that the data read situandolo in a space open to the sky. When the GPS reads data, the led flashes indicating that we have more than 4 satellites are available.
** if you turn off GPS the next time you read in dev/bus/usb/001/002 ...
* To simplify the start you can configure the application in automatic mode to start in as soon as you plug in the GPS USB
****ENJOY OUR GPS WITH ALL KIND OF MAPS.. TESTED WITH SYGIC AURA APK / EARTH / MAPS etc****
The application USB GPS INFO APK Globalsat installed the drivers for PL2303 automatically and activate the module USB GPS on Android automatically.
PL2303 USB SERIAL driver Android module PL2303 GPS USB application PL2303GPSinfo.apk
We accept orders by the following methods:
Online (secure): browse our range and add products to your basket.
Offline: please see the contact us page for telephone, fax, and email details (you can change your country by clicking on the link at the top of the page). Shipping prices vary across our product range and can be viewed for each product on the product datasheet by choosing the country you are in.
Express international delivery & worldwide shipping.
All in-stock orders received Monday through Fridays are shipped the same day. For customers in Europe, the deadline for same day dispatch is 16:00pm. Orders received after these deadlines are shipped the next business day. You can check availability by viewing the datasheet which will display a yellow check mark if the product is in stock availability check mark.
Quality is important to Siliceo online Therefore if a product does not perform as described on the datasheet please notify us within 24 months of delivery using the contact form and our dedicated team of scientific experts will examine details of your protocol to determine whether the problem is protocol related or product related.
All payment details are described on the invoice that you will receive after your order is dispatched. The invoice will be sent to the billing address you specify and this can be different to the delivery address for the products.
We accept PayPal, credit card, cash on delivery, bank and wire transfer as methods of payment, for further details please contact us.